# Quick Answer: How Many Outlets Can You Run On A 12 2 Circuit?

## How far can you run 12 gauge wire on a 20 amp circuit?

The total circuit would be about 60 -70 feet in length.

It would only be supplying about 5 outlets and one light.

It would be a light load, running small things, no heaters or med/large equipment.

#12 provides reasonable performance up to about 100′ with general loads like you describe..

## How many outlets can you put on a 14 2 wire?

14–2 wire is allowed for a 15 Amp circuit, and at 120 Volts, 15 Amps x 120 volts = 1800 volt-amperes. So that would allow ten (10) receptacles, you would probably derate that to eight (8) for an 80% safety factor.

## How many lights can I put on one switch?

A basic 15A circuit will allow you to connect up to 1400 watts of lighting load. That can be one 1400w fixture or fourteen 100w fixtures. You can put all of them on one switch or use multiple switches. 100w incandescent bulbs are becoming extinct.

## Can I mix 12 and 14 gauge wire?

Anyway, the first subject is a bit touchy because it makes it difficult to perform an inspection when all of the wires coming into the panel are 12 but many of the circuits have 14 in them too. There is nothing against code mixing wire size for these circuits as long as the OCPD matches the smallest wire.

## How many outlets can be on a 15 amp circuit?

I’m ask so many times how many outlets and or lights can I put on a 15 amp or 20 amp breaker. Well NEC code does not have it listed that way. By rule of thumb you would stick with 8 to 10 outlets and or lights per breaker. Now this is of course they are 120 volts 60 Hz (USA or Canada).

## Can I wire lights and outlets on the same circuit?

My short answer to the question is that “Yes, lights and power outlets (a.k.a AC receptacles) can be on the same circuit controlled by a circuit breaker, especially in a single family residential house”. … The circuit branch controlled by the 15A circuit breaker has a couple of lights and AC outlets connected.

## How many outlets and lights can I put on a 20 amp breaker?

The total number of fixtures on any given circuit will be 1800 watts on a 15 amp circuit and 2400 watts on a 20 amp circuit. It is permissible to wire 2400 watts of lights and a dozen or so receptacles on the same20 amp circuit.

## Do outdoor outlets need to be on their own circuit?

The National Electrical Code has no requirement for exterior residential outlets to be on their own circuit. The receptacles must be GFCI and there is requirement for a minimum number of them (and distance from pools), but that’s about it.

## How many outlets can you daisy chain?

Electrical receptacles have two pairs of terminals so that you can daisy-chain multiple receptacles on a single circuit in an existing house.

## Can I replace a 15 amp breaker with a 20 amp breaker?

The answer: It’s possible, but not advisable without an electrician evaluating the situation. You should never just upgrade from a 15-amp breaker to a 20-amp one just because the current one is tripping. Otherwise, you may burn your house down via electrical fire.

## Can you use 15a outlets on a 20a breaker?

The fact that you are permitted to have 15A receptacles on a 20A circuit (with a 20A breaker) is because the current draw from from the appliance plugged into that recepticle will draw no more than 15A.

## Can you use 12 2 outlets?

As long as you have a 15A circuit breaker on that circuit, it’s OK to use 12/2 NM cable for your lights. Since the maximum current on the circuit will be 15A, you won’t need special switches. You should label the wire that it is 15A, not 20A, so that someone else doesn’t come along and treat it as a 20A circuit.

## Should I use 12 or 14 gauge wire?

14-gauge wire is the smallest allowed for the permanent wiring of a circuit. It is rated as able to carry up to 15 amps of current. 12-gauge wire is the next size larger and is allowed to carry up to 20 amps.

## Is it OK to use 12 gauge wire on a 15 amp circuit?

However, 12-gauge wire is acceptable on both 15- and 20-amp circuits, so some electricians use it exclusively when wiring a house.

## How many outlets can be on a 20 amp circuit?

10 receptaclesOne rule of thumb is to assign a maximum draw of 1.5 amps to each receptacle, which allows for 10 receptacles on a 20-amp circuit.